Prevent your water heater from malfunctioning too soon by maintaining it from time to time. Water heaters that have undergone frequent maintenance are more likely to stop working due to wear and tear. Avoid inconvenience by planning ahead right before your water heater breaks down.
It is important to turn off the heating source of the unit before carrying out repairs. Doing this prevents accidents from happening during the process. This should not be overlooked since a water heater can be dangerous if not handled properly. Turn off the cold water supply valve to stop water from entering the tank.
You can inspect your unit thoroughly by draining the tank beforehand. Make sure the power or gas supply is turned off before connecting a standard hose to the drain valve. Run the other end of the hose to a floor drain or gutter to avoid scalding. You can turn off the unit the night before draining it to protect your skin from scalding.
If you want to remove the sediments sitting at the bottom of the tank, you can flush them out by turning the cold water valve on. Make sure to remove the hose and replace it with a bucket right below the drain valve. Wait until the water runs clear before refilling the tank and switching it on.
Draining and flushing the tank should remove the sediments sitting inside. However, you may have to replace the unit if you keep on getting discolored and smelly water. Sediments may have been too excessive for the tank to handle.
Always check the anode rod of your unit to protect your tank lining from corroding. This sacrificial rod is responsible for absorbing all charged water molecules, preventing your tank from doing so. Keep it in good condition at all times and replace it as soon as it measures less than of an inch. To ensure proper anode rod installation, do not hesitate to ask help from a specialist.
If your unit keeps on having varying temperatures, you might want to check if you have a faulty thermostat. Set it between 120 to 130 degrees Fahrenheit to protect your water heater from overheating. Having a high temperature can cause the unit to corrode or explode easily. When this happens, you have no choice but to buy a replacement unit immediately.
Have your water heater inspected by a professional to see if the damage is beyond repair. At times like this, look for a replacement water heater to continue having access to warm water in your household. Select a replacement unit that will meet your hot water demands. Do your research to prevent you from buying a unit haphazardly.
It is important to turn off the heating source of the unit before carrying out repairs. Doing this prevents accidents from happening during the process. This should not be overlooked since a water heater can be dangerous if not handled properly. Turn off the cold water supply valve to stop water from entering the tank.
You can inspect your unit thoroughly by draining the tank beforehand. Make sure the power or gas supply is turned off before connecting a standard hose to the drain valve. Run the other end of the hose to a floor drain or gutter to avoid scalding. You can turn off the unit the night before draining it to protect your skin from scalding.
If you want to remove the sediments sitting at the bottom of the tank, you can flush them out by turning the cold water valve on. Make sure to remove the hose and replace it with a bucket right below the drain valve. Wait until the water runs clear before refilling the tank and switching it on.
Draining and flushing the tank should remove the sediments sitting inside. However, you may have to replace the unit if you keep on getting discolored and smelly water. Sediments may have been too excessive for the tank to handle.
Always check the anode rod of your unit to protect your tank lining from corroding. This sacrificial rod is responsible for absorbing all charged water molecules, preventing your tank from doing so. Keep it in good condition at all times and replace it as soon as it measures less than of an inch. To ensure proper anode rod installation, do not hesitate to ask help from a specialist.
If your unit keeps on having varying temperatures, you might want to check if you have a faulty thermostat. Set it between 120 to 130 degrees Fahrenheit to protect your water heater from overheating. Having a high temperature can cause the unit to corrode or explode easily. When this happens, you have no choice but to buy a replacement unit immediately.
Have your water heater inspected by a professional to see if the damage is beyond repair. At times like this, look for a replacement water heater to continue having access to warm water in your household. Select a replacement unit that will meet your hot water demands. Do your research to prevent you from buying a unit haphazardly.
About the Author:
Learn more about water heater repair tips . Stop by Brian Winters's site where you can find out all about water heater maintenance and how it can benefit you.
No comments:
Post a Comment