Extend the life of your water heater by performing regular maintenance. If you want to avoid spending too much on repairs, contact a specialist to help you inspect your unit properly. You'll be surprised how much money you can save by keeping your tank in good condition.
Before carrying out any repairs, do not forget to shut down its heating source. This is important to prevent accidents from happening during the process. Turn off the circuit breaker if you have an electric unit or the gas supply valve if you have a gas-fired heater. Do not forget to shut down the cold water supply valve to prevent water from entering the tank. This is essential to be able to inspect your unit thoroughly. Remind everyone in your household not to use the heater up until you're finished inspecting it.
Check the internal components of your tank and lift the anode in it. This rod is responsible for absorbing all the sediments inside, protecting your tank from rust and corrosion. You may have a deteriorated anode rod once you see metal wires around it. If you don't take action immediately, expect your water to get rusty and smell bad at the same time. Do not let your family ingest contaminated water since this can lead to serious health problems.
Magnesium anodes are best used if you have a soft water. However, if the water is hard and softened heavily with salts, it's better to use an aluminum rod. To fight the effect of sulfur smell, use a zinc anode rod instead. You can ask a specialist what kind of anode rod will be suitable for your water heater.
Having too much sediment inside the tank can result to damaged lower heating element. To avoid this problem, simply flush and drain your water heater regularly. Hard water minerals at the bottom of the tank can convert into superheated steam. When this happens, you may start hearing strange noises from your water heater. Take note that a water heater can convert into a dangerous appliance if not dealt with properly.
It is important to look for signs of leaks in the early stage to prevent further damage. Water usually leaks if you have loose fittings and valve. Use a Teflon tape to wrap around the threading before tightening the pipes with a wrench. Replace badly damaged pipes to avoid developing rust stains in other areas of the water heater.
If you want to cut back on your electric bill, you might as well consider buying a replacement unit. Nowadays, water heaters are designed to be more efficient, meeting your hot-water demands while consuming less energy as it used to. You can always consult a specialist if you need help in choosing the best water heater for your household.
By following the tips listed above, performing water heater maintenance shouldn't be so difficult. Stop spending too much on repairs and keep your water heater in its tip-top shape. Just in case the problem gets too complicated for you to handle, call a specialist right away.
Before carrying out any repairs, do not forget to shut down its heating source. This is important to prevent accidents from happening during the process. Turn off the circuit breaker if you have an electric unit or the gas supply valve if you have a gas-fired heater. Do not forget to shut down the cold water supply valve to prevent water from entering the tank. This is essential to be able to inspect your unit thoroughly. Remind everyone in your household not to use the heater up until you're finished inspecting it.
Check the internal components of your tank and lift the anode in it. This rod is responsible for absorbing all the sediments inside, protecting your tank from rust and corrosion. You may have a deteriorated anode rod once you see metal wires around it. If you don't take action immediately, expect your water to get rusty and smell bad at the same time. Do not let your family ingest contaminated water since this can lead to serious health problems.
Magnesium anodes are best used if you have a soft water. However, if the water is hard and softened heavily with salts, it's better to use an aluminum rod. To fight the effect of sulfur smell, use a zinc anode rod instead. You can ask a specialist what kind of anode rod will be suitable for your water heater.
Having too much sediment inside the tank can result to damaged lower heating element. To avoid this problem, simply flush and drain your water heater regularly. Hard water minerals at the bottom of the tank can convert into superheated steam. When this happens, you may start hearing strange noises from your water heater. Take note that a water heater can convert into a dangerous appliance if not dealt with properly.
It is important to look for signs of leaks in the early stage to prevent further damage. Water usually leaks if you have loose fittings and valve. Use a Teflon tape to wrap around the threading before tightening the pipes with a wrench. Replace badly damaged pipes to avoid developing rust stains in other areas of the water heater.
If you want to cut back on your electric bill, you might as well consider buying a replacement unit. Nowadays, water heaters are designed to be more efficient, meeting your hot-water demands while consuming less energy as it used to. You can always consult a specialist if you need help in choosing the best water heater for your household.
By following the tips listed above, performing water heater maintenance shouldn't be so difficult. Stop spending too much on repairs and keep your water heater in its tip-top shape. Just in case the problem gets too complicated for you to handle, call a specialist right away.
About the Author:
Want to find out more about water heater leaking , then visit Brian Winters's site to get advice on proper water heater repair.
No comments:
Post a Comment